Connects through the USB port for maximum speed with compatibility with all modern PCs and laptops.
Planet Cnc Usb Controller Software To OperateDoesnt require additional machine control software to operate the MK controllers.
Planet Cnc Usb Controller .Exe Is TheCNCUSBController.exe is the most frequent filename for this programs installer. It uses USB port which is available on all modern computers and laptops. This is a complete (softwarehardware) solution and it does NOT require any additional software (Mach3 is NOT needed). Youll find comprehensive guides and documentation to help you start working with GoodEnoughCNC Hybrid as quickly as possible, as well as support if you get stuck. Making with CNC USB Controller, Planet CNC Suggested Edits are limited on API Reference Pages You can only suggest edits to Markdown body content, but not to the API spec. I have all structure and mechical parts of the blacktooth cutter done. X - running and y and z-axis does not work, it moves step motors and controller positions X -axis works, and Y and Z does not work. If tests failed and working (x-axis setup) does not working in the new axis location, go the Planet-CNCFileSettingsAxes and check if your current non-working axis setup requires a inverted pulse. A simple multimeter(ohms) will work, just connect the positive and negative ends to one side of the same wire and if reading comes to 0.000, wire has continuity and if reads 0.L then there is a break in the wire and should be replaced. Y, and Z-axis does not work, it moves step motors and controller positions X -axis works, and Y and Z does not work.I used 425 oz-in motors Recommend first test to check a non-working axis, is to connect the current working axis(ex X-axis) to either the yz axis to test the actual board and wiring in other axis setup. Click the link to respond: I installed the USB CNC Planet software- 2.10.1406.1201., and got out of your USB controller 75. Y, and Z-axis does not work, it moves step motors and controller positions X -axis works, and Y and Z does not work.I used 425 oz-in motors ABSOLUTELY NOTHING WORKS. ANY HELP WOULD BE APRECIATED Did you install the Mach3 USB plug-in Make sure that you followed all of the steps and diagrams on the following page. ANY HELP WOULD BE APRECIATED I have the older discontinued USB breakout board. The y-axis no longer works and have traced it to the breakout board. Is there a replacement board that can use the same Planet CNC software running on Windows 10 No, we have gotten away from the planet-cnc boards as they have decided to not support our board with their software. You will be better off with Mach3 as a control software as this is widely used and supported. Is there a replacement board that can use the same Planet CNC software running on Windows 10 This USB controller: is based on PlanetCNC controller. Does this mean PlanetCNC API is fully compatible too Is any API functionality missing Inquiries about API functionality will need to be addressed to Planet-CNC. BuildYourCNC offers hardware support for the board, but software licensing is handled through Planet-CNC. Click the link to respond: This USB controller: is based on PlanetCNC controller. Planet Cnc Usb Controller Driver That IsDoes this mean PlanetCNC API is fully compatible too Is any API functionality missing I HAVE ONE OF YOUR SMALLER STEPPER MOTORS RUNNING MY X AXIS BRIDGE CRANE AND IF IT IS MOVED TO FAST THE MOTOR SOUNDS LIKE SKIPPING STEPS WILL 651OZ REQUIRE A DIFFERENT POWER SUPPLY CONTROLER Yes, the 651 ozin motor requires a driver that is compatible to the motors (the motor will draw 6 amps max and the driver paired with this motor will be able to allow for a 6 amp draw). I would also recommend a 36 volt power supply for better high velocity performance. Click the link to respond: I HAVE ONE OF YOUR SMALLER STEPPER MOTORS RUNNING MY X AXIS BRIDGE CRANE AND IF IT IS MOVED TO FAST THE MOTOR SOUNDS LIKE SKIPPING STEPS WILL 651OZ REQUIRE A DIFFERENT POWER SUPPLY CONTROLER I have one of your smaller stepper motors running my X AXIS bridge crane and if it is moved to fast the stepper motor sounds like it is skipping steps will the 651oz stepper motor require a different power supply and controler Yes, the 651 ozin motor requires a driver that is compatible to the motors (the motor will draw 6 amps max and the driver paired with this motor will be able to allow for a 6 amp draw). Click the link to respond: I have the usb breakout board and need to run the A axis as a slave the software greys out the box how do I fix this Absolutely nothing works.
0 Comments
Leave a Reply. |